Workshop
Ask a question

Topics with Label: Building and Construction

Mish28
Just Starting Out
1 reply

Using 900mm Kaboodle Tall Pantry Carcass with three metal sided drawers installed below. I will cut the top off the pantry carcass - just above the dr ...

Marinerescuelea
Just Starting Out
1 reply

small budget, 2000mm long with a set of drawers for cutlery a under bench space for two bar fridges, functional bench top what do you recommend also I ...

wpatters1229
Just Starting Out
1 reply

I have the subfloor which is tongue and groove boards and I want to place Masonite over the top for peel-and-stick tiles. Can I use construction adhes ...

Edgar
Cultivating a Following
10 replies

I.want to install this benchtop piece (1600mm x 400mm) as a breakfast bar. I would like advice regarding my.options for installation. The wall it is ...

deancarlo
Just Starting Out
3 replies

Hi guys. Im looking at finally adding some shelving to our pantry. We want floating shelves and want your advice on my plans - mainly on the framing ...

RenovationDream
Just Starting Out
1 reply

Hello all! I'm keen to place a long floating shelf in my kitchen. Approximately 2.4 + meters but I can only find shelves for 1.2 m How do I crea ...

ching9l
Finding My Feet
4 replies

Hello! Can I please ask what are some possible options for extending the kitchen white melamine shelves to the ceiling. The house has a 2.5m ceiling h ...

theDIYedit
Making a Splash
1 reply

I am mid-kitchen renovation and I have hit a bit of a snag - such is the life of a DIY-er! I am installing 2 ovens side by side under the benchtop - p ...

gwilso
Just Starting Out
2 replies

Hello, I am building a Kaboodle kitchen in the thermoformed Cremesala colour with the country style profile. However, the pantry needs to be ripped ...

LeopoldProjects
Growing in Experience
18 replies

Hello,I am building a kaboodle kitchenette. The corner cabinet is to have a hot water tank inside it. The drip pan/tray is the same depth as the cabin ...

rebelliouskiwi
Finding My Feet
4 replies

We bought a house and it has this pokey pantry with metal shelving which I don't like, I have the same ones in my garage and they are sharp. Any ...

Summer4eva
Getting Established
7 replies

Hi everyone, just got a question about a rangehood installation. I live in a unit with tiled roof. I was told 2 options: 1, the pipe can duct past the ...

MaTH
Finding My Feet
1 reply

My local Bunnings store sell bench top boards but are hesitate to cut sink holes, so how?

Dirk
Just Starting Out
1 reply

How do you cut Bellessi splasback polymer. Also how to attack to a chipboard backing

MaxB
Growing in Experience
1 reply

Purchased a new apartment and could feel oven moves when opening and closing the door. Today removed oven door to clean and noticed the two screws tha ...

DianeTDoyle
Growing in Experience
6 replies

HI All, I am looking for suggestions on how to make a wine rack using reo steel reinforcing mesh. What should I look out for as top tips to make it st ...

sportyrom
Growing in Experience
6 replies

I built this wine rack out of necessisity than need. I was replacing my existing fridge with a bigger one, so I had to remove the cabinet above the fr ...

jase2
Building a Reputation
9 replies

I'm planning to make pour in place concrete countertops for a new kitchen and I was wondering if anyone had done this and had some feedback to shar ...

JakeP88
Finding My Feet
3 replies

  What is the best way of installing floating shelves underneath the work top? I’m unsure about which drill bit to use for this

wilkos
Getting Established
5 replies

    Hi all, I’m building an outdoor kitchen with Kaboodle and wanting to know the best way to measure etc to get the clips in the right spot to be a ...

Tadmore
Finding My Feet
4 replies

I'm planning a kitchen renovation where there are two pillars/posts in the middle of the area, which limit the use of space. The pillars support the ...

Novaps1
Just Starting Out
3 replies

Hi, I purchased some Kaboodle Heritage profile 450mm doors to suit a Kaboodle 450mm pantry. The doors have 5 hinge holes that do not align with the 4 ...

tl91
Just Starting Out
3 replies

We are doing a new kitchen at the moment and have selected brick facings as our splashback finish. Can these facings be adhered directly to a plasterb ...

Willfisher
Finding My Feet
3 replies

Kitchen Renovation and addition of new Butler's pantry. The project involved changing the old-style kitchen with dated cabinets and benchtop/splashb ...