Steps

12345

Step 1

1/5

 

Review manufacturer guidelines and drill routing holes.


Begin by assessing the routing of your dishwasher's inlet and waste hoses. Refer to the manufacturer's guidelines regarding allowable elevations of the hoses and follow them closely during installation. Proper hose routing helps prevent kinks and ensures efficient water flow.


The allocated space for a dishwasher often has a cabinet panel between it and your connections. To allow access, this panel must have routing holes drilled in it. Take your 44mm hole saw and drill two intersecting holes in the cabinet panel for your hoses.

 

1.1 Hoses to be routed.jpg 1.2 Drilling holes in cabinet panel.jpg 1.3 Holes drilled in cabinet panel.jpg

Next Step

Step 2

2/5

 

Feed hoses through your holes and install the return bracket.


Push the inlet and waste hose through the holes in the cabinet panel.


Many dishwashers require you to elevate the waste hose before returning it back down and connecting it to your sink S-bend. Install any provided return bracket at the specified height by the manufacturer with the timber screw and drill driver. Clip the waste hose into it.

 

2.1 Hoses routed through cabinet.jpg 2.2 Attaching Waste hose return.jpg 2.3 Waste hose return fixed in position.jpg

 

Previous StepNext Step

Step 3

3/5

 

Identify connections and connect inlet hose.


Dishwashers have a larger waste hose and a thinner inlet hose. Some models come with two inlet hoses for both hot and cold connections. The inlet hose has a screwed connector, and you'll need to connect it to the small tap located on the rear wall of the cabinet.


Take the inlet hose connector and align it with the tap threads. Ensure it is not misaligned and screw it onto the tap. If your machine has a hot water hose, connect it as above to the hot water tap.


You can use multi-grip pliers if you have difficulty tightening the connector by hand. However, do not overtighten the fitting as you could damage it.

 

3.1 Identifying connections.jpg 3.2 Mini cock tap.jpg 3.3 Dishwasher inlet hose.jpg 3.4 Screwing on inlet hose.jpg 3.5 Inlet hose attached.jpg

 

Previous StepNext Step

Step 4

4/5

 

Drill out the S-bend trap spigot (if necessary).


The waste hose needs to be connected to your sink's S-bend trap. Most S-bend traps include a barbed spigot that the rubber end of the waste hose pushes onto. If a dishwasher has not been installed previously, drill out this spigot with a 13mm drill bit and your drill driver. Ensure you only drill out the internal blocking wall and do not drill further inside the pipe.

 

4.1 Waste spigot.jpg 4.2 Dishwasher outlet hose.jpg 4.3 Placing drill bit in spigot.jpg 4.4 Drilling out spigot.jpg

 

Previous StepNext Step

Step 5

5/5

 

Connect the waste hose.


Add your hose clamp onto the rubber fitting of the waste hose. Push the waste hose onto the barbed spigot. Tighten the strap hose clamp with your flathead screwdriver.


Run a cycle on your dishwasher and check for leaks periodically. Tighten the connections if any leaks are found.


You have now successfully connected your dishwasher. 

 

5.1 Placing strap clamp on waste hose.jpg 5.2 Pushing waste hose onto spigot.jpg 5.3 Tightening hose clamp.jpg 5.4 Hoses connected.jpg

 

 

 

Previous Step

Materials

Tools

  • 17 - 32mm Stainless steel hose clamp
  • 20mm timber screw.
  • Drill driver
  • 13mm drill bit
  • Flathead screwdriver
  • Hole saw kit
  • Multi-grip pliers.

Images

1.1 Hoses to be routed.jpg1.2 Drilling holes in cabinet panel.jpg1.3 Holes drilled in cabinet panel.jpg2.1 Hoses routed through cabinet.jpg2.2 Attaching Waste hose return.jpg2.3 Waste hose return fixed in position.jpg3.1 Identifying connections.jpg3.2 Mini cock tap.jpg3.3 Dishwasher inlet hose.jpg3.4 Screwing on inlet hose.jpg3.5 Inlet hose attached.jpg4.1 Waste spigot.jpg4.2 Dishwasher outlet hose.jpg4.3 Placing drill bit in spigot.jpg4.4 Drilling out spigot.jpg5.1 Placing strap clamp on waste hose.jpg5.2 Pushing waste hose onto spigot.jpg5.3 Tightening hose clamp.jpg5.4 Hoses connected.jpg
12 Replies

Why join the Bunnings Workshop community?

Workshop is a friendly place to learn, get ideas and find inspiration for your home improvement projects