How to remove stuck bathroom spout?

[paddy1829]

 

 

 

Hi Team,

bathroom spout is stuck and wont not budge -

tried WD40 and Heat but it wont move. 

Sliced bahind flange just in case there is any slicone but there is no slicone adhesive. 

seems like a centre part is holding onto 

do I need to cut flange with a grinder ?

second issue:

spindle is bit shorter in the estilla bath kit than the original spindle in the photos - would Kinetic 15mm spindle extension work ? 

Thank You appreciate it. 

[PlumbMaster-Zee]

Hi Paddy1829,

It seems like the spout is broken and the cover plate is stuck. Regarding the issue with the stuck bathroom spout and the cover plate, here’s a detailed process to address it:

Turn Off Water Supply: Ensure the water supply to the bathroom is turned off to prevent any leaks or water damage.

Inspect the Pipe: Use a flashlight to check inside the exposed pipe for any remaining fragments or obstructions.

Remove Broken Pieces: Needle-Nose Pliers: Carefully extract any broken pieces inside the pipe using needle-nose pliers. Internal Pipe Wrench: If pliers are ineffective, use an internal pipe wrench to grip and remove any stuck pieces.

Apply Penetrating Oil: Apply penetrating oil (such as WD-40) inside the pipe and let it sit for a while to loosen any corrosion or mineral buildup.

Use an Easy-Out Tool: For threaded broken pieces, use an easy-out tool (screw extractor): Insert the tool into the pipe and turn it counterclockwise to grip and remove the stuck piece.

Clean the Threads: Clean the threads inside the pipe with a wire brush to ensure they are free of debris and corrosion.

Check for Damage: Inspect the pipe for any damage. Replace the section if necessary.

Removing the Stuck Cover Plate (Escutcheon):

Turn Off Water Supply: Ensure the water supply is turned off.

Inspect for Screws: Look for visible screws around the edge of the cover plate. Use an appropriate screwdriver to remove them if present.

Check for Silicone or Caulk: The cover plate may be sealed with silicone or caulk. Use a utility knife to carefully cut around the edge to break the seal without damaging the wall or tiles.

Gently Pry Off the Cover Plate: Use a thin, flat tool like a putty knife or flathead screwdriver. Insert it between the cover plate and the wall. Gently pry the cover plate away from the wall. Work your way around the plate, prying a little at a time to gradually loosen it.

Apply Heat if Necessary: If the cover plate is particularly stubborn, apply heat with a hairdryer to soften any adhesive. This can make it easier to remove.

Clean the Area: Once removed, clean the area to remove any remaining adhesive, silicone, or caulk.

Addressing the Spindle Issue:

Kinetic 15mm Spindle Extension: To compensate for the shorter spindle in your Estilla bath kit, use a Kinetic 15mm spindle extension. Ensure it’s compatible with the existing spindle and properly fitted and secure.

General Tips:

Heat Application: Carefully apply heat using a hairdryer or heat gun around the spout to expand the metal, making it easier to remove. Be cautious not to overheat surrounding materials.

Gentle Tapping: Use a rubber mallet or a wooden block and hammer to gently tap around the spout to loosen any corrosion or mineral buildup.

Protect the Wall: Place a thin piece of cardboard or cloth behind the putty knife or screwdriver to protect the wall or tiles from scratches.

Be Patient: Take your time to avoid damaging the cover plate, wall, or tiles.

If you encounter any difficulties or need further assistance, it might be best to consult a professional plumber.

Good luck

 Zee

[EricL]

Hello @paddy1829 

Welcome to the Bunnings Workshop community. It's marvellous to have you join us, and thanks for sharing your question about your bath spout. 

It appears to be a traditional bath spout like the Shaw & Mason Chrome Standard Bath Spout or similar. If you are not using the flange that is left on the wall for any other purpose, I suggest using a Trojan 300mm Multigrip Plier to hold onto the side of the flange and turn it anti-clockwise. 

It might take several attempts so please keep at it until you get a good grip. Please note that the multigrips will damage the side of the existing flange. 

In regards to the spindle, I suggest putting the Estilo spindle and the old one side by side to make sure that they are not the same height. If they are not, then I suggest getting a Kinetic 15mm Wall Tap Spindle Extender - 2 Pack to match the heigh of the old set.

If you have any other questions we can help with, please let us know.

Eric

[paddy1829]

Thank You PlumbMaster-Zee and EricL for your reply and helping me with 

for step by step guide. It helped to remove this stubborn spout.
and I also added Kinetic 15mm extension for flange to attach onto the thread. 

 

 

now have to find a new spout in bunnings to attach to the existing thread length size , which is about 20mm

the one in Estillo kit has 15mm thread length. So about 5mm shorter. 

Have a great day and Thanks heaps