Workshop
Ask a question

Topics with Label: Building and Construction

Homebush12
Community Newcomer
1 reply

Your instructions to install an Estilo SMS 4 lip shower base stipulate a 1:3 cement:bricky sand mix. I have no problem with that but am curious as to ...

daisyinthewild
Just Starting Out
4 replies

Hi, I have a very small laundry, there is existing cabinetry, however the laundry was built with a top loader washing machine in mind, but now we have ...

Youngster
Finding My Feet
5 replies

Can I use a Kaboodle cabinet for a wall-hung bathroom vanity? To fit basin in photo, measurements 920mm x 470mm with drop in basin 280mm depth (back t ...

claireh88
Just Starting Out
1 reply

Hello, I started a refurb project in my laundry and discovered that the section of the ceiling that is lower is not connected to the wall and is there ...

macacom
Just Starting Out
2 replies

I want to build a laundry bench 700mm deep and 1900mm wide. From right to left looking at it I want to have a 500 by 400 tub then a front load washe ...

Mark76
Just Starting Out
1 reply

I’m doing a full bathroom renovation at the moment due to several bad water leaks in an old house. I need to build 2 small walls as part of the work. ...

flutes
Finding My Feet
11 replies

Hi, We have a Estilo 900 x 1830mm Chrome Semi Frameless Shower Screen. It says it's reversible but doesn't really say how.There's a very brief mention ...

tmarsh
Finding My Feet
3 replies

Hi, We are having our bathroom renovated and having some issues. 1. Due to some errors in measurement, the screed needed to be cut back and now the ...

damien-22
Cultivating a Following
2 replies

Can this be tiled over? used as a backing behind a tiled wall? https://www.bunnings.com.au/james-hardie-2400-x-900-x-4-5mm-2-16m-hardieflex-cladding_p ...

throatgoat
Just Starting Out
3 replies

im looking at installing vj panelling into my bathroom and am questioning a few things. Firstly when installing the panelling do they go direct to s ...

Lennock
Finding My Feet
7 replies

I am building an internal laundry under my stairs using a 70mm x 45mm framing pine, and 18mm MDF paneling. I will put sound reduction paneling within ...

AGK
Just Starting Out
2 replies

Hello, I have recently laid down a James Hardie Secura floor and Villaboard walls in a 2mx1.9m bathroom. It is a room with a framed bath and a vanity. ...

Sedg
Growing in Experience
25 replies

Hello again i posted a question regarding framing the other week and recieved some great help, thank you. now i am measuring and locating where the ne ...

cooljohn_jc16
Just Starting Out
1 reply

Tshelf
Growing in Experience
5 replies

I've got a bathtub that's not in use so I want to turn it into a storage/workspace. I have a couple questions about how to approach it. I want to make ...

Luke2001
Finding My Feet
3 replies

Hi all, Currently in the Demo phase of a bathroom and laundry reno. We're planning on installing hardie vj panelling (groove lining) as a feature wa ...

JodieQ
Just Starting Out
1 reply

Do the VJ lining boards go on top of the plaster, or do we remove the plaster

Smitho1
Just Starting Out
3 replies

Do you have to use a joiner between every sheet when installing Wall Art wet Area Wall Panels or do they butt up to each other?

jeffl_au
Growing in Experience
1 reply

Need a bench top that spans both washing machine and dryer. hoping to avoid a support panel in between, but worried about whether the span is too l ...

BB11
Finding My Feet
4 replies

Can the water supply taps for a top loader washing machine be in the cupbaord)? Can a drain hose for a top loader washing machine be at any height? ...

twocutekelpies
Making a Splash
1 reply

I spent ages looking for a linen cupboard for this space, but found them to be too short, too shallow, too wide or too hard to assemble so after conve ...

Kapster
Growing in Experience
5 replies

I have a laundry wall which is fibre cement sheeting, it’s probably about 15-20mm thick, hard to say. I bought two packs of the Ramsay hollow wall anc ...

Dani64
Growing in Experience
6 replies

   hi community! I’m making these bathroom benches from hardwood sourced from an old deck BUT Im not happy with them and need help with legs, 2 I’ve ...

crisis
Cultivating a Following
10 replies

Hello friends, I successfully removed the concrete bed under the old bath , without damaging the slab, with the help of some workshop members' advice ...